- 您现在的位置：买卖IC网 > Sheet目录411 > EK43703-01 (Peregrine Semiconductor)KIT EVAL FOR PE43703 DSA
PE43703
Product Specification
Evaluation Kit
The Digital Attenuator Evaluation Kit board was
designed to ease customer evaluation of the
PE43703 Digital Step Attenuator.
Direct-Parallel Programming Procedure
For automated direct-parallel programming,
connect the test harness provided with the EVK
from the parallel port of the PC to the J1 & Serial
header pin and set the D0-D6 SP3T switches to the
‘MIDDLE’ toggle position. Position the Parallel/
Serial ( P / ? S) select switch to the Parallel (or left)
position. The evaluation software is written to
operate the DSA in either Parallel or Serial-
Addressable Mode. Ensure that the software is set
to program in Direct-Parallel mode. Using the
software, enable or disable each setting to the
desired attenuation state. The software
Figure 31. Evaluation Board Layout
Peregrine Specification 101-0312
Note: Reference Fig. 32 for Evaluation Board Schematic
automatically programs the DSA each time an
attenuation state is enabled or disabled.
Serial-Addressable Programming Procedure
For manual direct-parallel programming,
disconnect the test harness provided with the EVK
from the J1 and Serial header pins. Position the
Parallel/Serial ( P / ? S) select switch to the Parallel (or
left) position. The LE pin on the Serial header must
be tied to V DD . Switches D0-D6 are SP3T switches
which enable the user to manually program the
parallel bits. When any input D0-D6 is toggled
‘UP’, logic high is presented to the parallel input.
When toggled ‘DOWN’, logic low is presented to
the parallel input. Setting D0-D6 to the ‘MIDDLE’
toggle position presents an OPEN, which forces an
on-chip logic low. Table 9 depicts the parallel
programming truth table and Fig. 30 illustrates the
parallel programming timing diagram.
Position the Parallel/Serial ( P / ? S) select switch to
the Serial (or right) position. Prior to
programming, the user must define an address
setting using the ADD header pin. Jump the
middle pins on the ADD header A0-A2 (or lower)
row of pins to set logic high, or jump the middle
pins to the upper row of pins to set logic low. If
the ADD pins are left open, then 000 become the
default address. The evaluation software is
written to operate the DSA in either Parallel or
Serial-Addressable Mode. Ensure that the
software is set to program in Serial-Addressable
mode. Using the software, enable or disable each
setting to the desired attenuation state. The
software automatically programs the DSA each
time an attenuation state is enabled or disabled.
Latched-Parallel Programming Procedure
For automated latched-parallel programming, the
procedure is identical to the direct-parallel method.
The user only must ensure that Latched-Parallel is
selected in the software.
For manual latched-parallel programming, the
procedure is identical to direct-parallel except now
the LE pin on the Serial header must be logic low
as the parallel bits are applied. The user must then
pulse LE from 0V to V DD and back to 0V to latch the
programming word into the DSA. LE must be logic
low prior to programming the next word.
?2008-2009 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0245-05
│ UltraCMOS? RFIC Solutions
Page 12 of 15
Logo updated under non-rev change. Peregrine products are protected under one or more of the following U.S. Patents: http://patents.psemi.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
EK64904-01
KIT EVAL FOR 64904 NO CABLES
EK64905-11
KIT EVAL FOR 64904 W/CABLES
EKL3104
D-IMAGER 3D IMAGE SENSOR
EKL3105
3D IMAGE SENSOR-HIGH PRECISION
EKL3106
3D IMAGE SENSOR-HIGH PRECISION
EKMB1301111K
SENSOR PIR
EKMC1603113
SENSOR MOTION PIR 12M RANGE WHT
ELB-1001SDRWA/S530-A3
DISPLAY 10 BAR GRAPH DEEP RED CC
相关代理商/技术参数
EK43704-11
制造商:Peregrine Semiconductor 功能描述:FREQUENCY CONTROL EVALUATION BOARD
EK43705-11
功能描述:EVAL KIT FOR RF DSA 7BIT 50OHM 制造商:peregrine semiconductor 系列:UltraCMOS?，HaRP?? 零件状态:有效 类型:衰减器 频率:50MHz ~ 8GHz 配套使用产品/相关产品:PE43705 所含物品:板 标准包装:1
EK43711-02
功能描述:EVAL BOARD FOR PE43711 制造商:peregrine semiconductor 系列:UltraCMOS?，HaRP?? 零件状态:有效 类型:衰减器 频率:9kHz ~ 6GHz 配套使用产品/相关产品:PE43711 所含物品:板 标准包装:1
EK43712-02
功能描述:EVAL BOARD FOR PE43712 制造商:peregrine semiconductor 系列:UltraCMOS?，HaRP?? 零件状态:有效 类型:衰减器 频率:9kHz ~ 6GHz 配套使用产品/相关产品:PE43712 所含物品:板 标准包装:1
EK43713-02
功能描述:EVAL BOARD FOR PE43713 制造商:peregrine semiconductor 系列:UltraCMOS?，HaRP?? 零件状态:有效 类型:衰减器 频率:9kHz ~ 6GHz 配套使用产品/相关产品:PE43713 所含物品:板 标准包装:1
EK4408X05XA-D5X WAF
制造商:Fairchild Semiconductor Corporation 功能描述:
EK4410F05XA-D5X WAF
制造商:Fairchild Semiconductor Corporation 功能描述:
EK4410F06XA-D6X WAF
制造商:Fairchild Semiconductor Corporation 功能描述: